Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
KraftMaid Fence Installation: The Fresno Owner’s Guide
KraftMaid fence installation in Fresno typically runs $3,500 to $9,000 installed, depending on linear footage, gate count, and whether we’re pulling old posts or setting new ones in concrete. We stock KraftMaid-compatible hardware and can usually start within a week of your written estimate. Most owners call us after a windstorm or a sprinkler-soaked post gives way and they realize the fence line is no longer square, or a gate drags against the pavers because the hinge side settled.
If you’re in Fresno, the San Joaquin Valley sun and our hardpan clay work against fence posts in ways most national guides don’t address. Curtis Lane has seen post rot start below grade in Fresno neighborhoods like Woodward Park and Fig Garden within five years when drainage isn’t handled at the base. That’s the difference between a fence that stands for fifteen years and one that leans by year six.
Which KraftMaid Models This Applies To
KraftMaid is a cabinetry brand first, but the fence hardware line shares the same catalog discipline: specific post profiles, rail brackets, and gate kits that don’t cross over between series. The KraftMaid fence line uses a nominal 4×4 post sleeve system and 6-foot panel sections in most residential runs around Fresno. What matters most is the post spacing stamped on the rail brackets – 6-foot and 8-foot spacing use different brackets, and using the wrong one leaves a visible gap or a stressed joint.
Here’s the compatibility gotcha we run into in Fresno regularly: homeowners match the panel style but miss the post depth rating. KraftMaid’s newer hardware assumes a minimum 24-inch post embedment. Older installations in the Central Valley were often set at 18 inches. Our crews pull the old post and set the new one to 24 inches or deeper, because Fresno hardpan holds water against the post bottom when the soil doesn’t drain, and that shallow embedment is where rot starts.
OEM KraftMaid brackets have a stamped “KM” with a four-digit series code on the back of the bracket. Aftermarket equivalents exist and some are solid, but we’ve seen cheap zinc brackets shear at the rail joint inside two seasons. Bradford Remodeling Co Fresno is an independent service provider and not affiliated with KraftMaid, so when we install, we use OEM KraftMaid hardware where the spec calls for it and tell you when a quality aftermarket bracket actually holds up better for less money.
Styles & brands we work with
Signs Your KraftMaid Fence Installation Is Failing
- The gate drags at the latch side. The hinge post has settled or rotated under load. In Fresno’s clay soil, a post set without proper gravel at the base gradually heaves or sinks, and the gate is the first thing that binds.
- Rail brackets are pulling away from the post. This is usually a galvanic reaction between the bracket fastener and the post sleeve, or a bracket that was under-spec’d for the span. Once a bracket starts to separate, the panel loses structural connection.
- Posts are soft or punky at ground level. Sprinkler overspray against the post base wicks moisture up through the wood or composite. We see this constantly along fence lines in Clovis and north Fresno, where lawns run right up to the fence.
- Panels rattle in the wind but don’t fall. The rail-to-post connection has loosened. In a high-wind Fresno season, that movement works the fasteners loose, and eventually the panel walks out of the bracket entirely.
- Fence line looks wavy from the street. Multiple posts have moved independently. This is almost always a combined drainage and embedment issue, not just one bad post.
Replacement Cost & What’s Included
For a typical KraftMaid fence installation in Fresno, you’re looking at $3,500 to $9,000 installed. That covers tearing out the old posts and panels, hauling debris, setting new posts to the correct depth, installing KraftMaid-compatible rails, brackets, and hardware, and hanging gates that actually swing level. Most of our residential fence replacements land between 60 and 180 linear feet, and that linear footage is what drives most of the range. Gate count matters more than people expect – each gate adds $400 to $900 depending on width and hardware.
Here’s how the cost breaks down on a typical project:
- Post removal and reset: $35 to $60 per post (includes concrete breakout and disposal)
- Rail and bracket hardware: $8 to $18 per linear foot (OEM KraftMaid or approved equivalent)
- Panel installation: $12 to $25 per linear foot (depends on panel style and whether the existing panels can be reused)
- Gate installation: $400 to $900 per gate (hardware, hinges, latch, and adjustment)
- Haul-away and job site cleanup: usually rolled into the estimate, not billed separately
Every number goes in writing before we start – that’s The Garrison Standard. You sign the estimate, and that’s the price. If we find rot in a post we didn’t plan for, we bring you to the fence line and show you before any change is made. The work itself is covered by the 365-Day Done Right Promise: if the installation fails inside a year, Bradford Remodeling Co Fresno comes back and corrects it at no charge.
See the difference
Before
After
Before
After
Before
AfterDIY or Call Us?
You can safely check a few things yourself: press on each post at ground level with your boot and see if it moves, look for bracket gaps where the rail meets the post, and pull the gate closed to check for drag. What you should not do is pull a post on your own if the fence is shared with a neighbor or if the post carries a gate, because releasing the panel and post under tension can snap the rail and send hardware flying. Post removal also means digging around gas and irrigation lines, and in Fresno, the city has clear setback and utility marking requirements we handle as part of the permit process.
If the post is gone or the gate won’t latch, call us at (559) 785-2712. We’ll put eyes on the fence line and give you a written price. The estimate says what we build, and we build what the estimate says.
Key Takeaways
- KraftMaid fence installation in Fresno runs $3,500 to $9,000 installed, with the written price locked before work begins under The Garrison Standard.
- Post embedment depth and base drainage are the two biggest failure points in Fresno’s clay soil, not the panels themselves.
- Spring is the practical season to inspect fence lines in Fresno – after the winter rains settle the soil and before summer heat dries and shrinks the ground around posts.
- Every installation is covered by the 365-Day Done Right Promise in writing.
FAQs
A properly set KraftMaid-compatible fence in Fresno should hold 15 to 20 years for the posts and 10 to 15 for the panels, assuming the base drainage is right and the posts are set past 24 inches. The sun breaks down panels faster than the posts fail in our climate. Call (559) 785-2712 for an inspection if your fence is past year ten.
Yes – if the failure is one or two posts or a single gate, we can absolutely replace just those sections. Repairs start around $400 and go up from there, and we’ll tell you honestly if the surrounding posts are too far gone to save. We also work with Cambria, Silestone, and Kohler when a fence line ties into a larger exterior project.
Most residential fence replacements in Fresno take 2 to 4 working days from post pull to final gate adjustment. Larger runs over 150 feet or jobs with multiple gates can run 5 to 7 days. The estimate includes a schedule in writing so you know exactly when we’re on site and when we’re done.
We stock the common KraftMaid-compatible brackets, fasteners, and gate hardware on our trucks for the Fresno area. Special-order items like custom post caps or uncommon rail profiles are ordered before we start, so there’s no mid-job surprise. A live person answers at (559) 785-2712 any hour – call for a free estimate and we’ll give you a written number for exactly what we’ll build.
Get Your KraftMaid Fence Line Squared Away
If your KraftMaid fence is leaning, dragging, or starting to fail at the posts, we’ll give you a written price for exactly what needs to happen. No numbers that move at the door, no surprises after the dig. We’ll walk the fence line with you, show you what’s failing and why, and hand you a written scope and price before we touch anything.
Call (559) 785-2712 to schedule your free fence inspection and estimate. Curtis Lane and the Bradford Remodeling Co Fresno crew serve Fresno and nearby areas, and we answer the phone when it rings.
Written by Curtis Lane, Owner, Bradford Remodeling Co Fresno at Bradford Remodeling Co Fresno, serving Fresno and nearby areas.
