Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Tamko Fence Installation: The Fresno Owner’s Guide
Tamko fence installation in Fresno typically runs $3,500 to $9,000 for a full perimeter project, with most standard residential lots falling between $4,500 and $6,500. We stock Tamko-compatible posts, pickets, rails, and hardware, and our crew can usually start within a week of your written estimate. Most Fresno homeowners discover they need this work after a windstorm snaps a post at the substrate line or they notice the fence leaning 6 to 8 inches off plumb along the property line.
Which Tamko Models This Applies To
Tamko’s fencing line splits into two main product families: the Heritage series (wood-composite privacy panels) and the EverGrain composite picket systems. The Heritage line uses a 5/8-inch-thick tongue-and-groove board with a steel-reinforced aluminum bottom rail, while EverGrain runs a 3/4-inch solid-core picket on a two-rail configuration. The compatibility gotcha most owners miss: Heritage panels are not interchangeable with EverGrain pickets because the post routs are cut at different depths. If your fence has a Tamko branding sticker on the post cap, pull that measurement before ordering anything. The stamped post dimensions (typically 4×4 or 5×5 on newer runs) tell you which replacement parts will actually seat correctly.
On the OEM-versus-aftermarket question: for Tamko specifically, the OEM post sleeves and rail brackets are engineered with a tighter tolerance than most generics. We’ve seen aftermarket post caps warp within two Fresno summers because they lack the UV stabilizer that Tamko bakes into their composite recipe. For fasteners and concrete footings, quality aftermarket equivalents hold up fine. For anything structural, we spec OEM.
Styles & brands we work with
Signs Your Tamko Fence Installation Is Failing
- Post lean greater than 5 degrees: You’ve got a footing failure, usually from Fresno’s clay-heavy soil expanding and contracting through wet-dry cycles. The post may still look intact above ground, but the concrete pad underneath has cracked or sunk.
- Rail brackets pulling free from posts: This is a fastener problem, and it’s common where installers used drywall screws instead of rated structural screws. The brackets hold until the first good valley wind, then start sawing through the post material.
- Warped or cupping pickets near sprinkler heads: Composite doesn’t rot, but it does soften when it’s soaked daily. Fresno irrigation runoff hitting the bottom 12 inches of a Tamko picket will cup it within two years if the sprinkler isn’t redirected.
- Gaps opening between panels at the corner posts: The fence has racked. It’s not cosmetic; a racked corner puts shear load on the post-to-rail connection and the whole section will follow given time.
- Ground clearance disappearing along one run: Fresno’s sandy loam in neighborhoods like Woodward Park settles differently than the hardpan south of Shaw. A fence that started at 2 inches of clearance can be buried to grade in five years, which traps moisture against the bottom rail and accelerates failure.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
A full Tamko fence installation in Fresno lands between $3,500 and $9,000, and the spread comes down to three things: linear footage, post spacing, and whether we’re pulling the old fence or building fresh. A standard 150-linear-foot backyard with 6-foot Heritage privacy panels, steel-reinforced rails, and concrete footings runs $4,500 to $6,500 installed. If your project needs retaining-wall integration, custom gate fabrication, or the soil is rocky hardpan that fights the auger, expect the high end.
You get a written line-item price before we cut a single post hole. That price covers demolition and haul-away of the old fence, all Tamko-compatible materials, concrete footings poured to 24 inches below grade, brackets, hardware, and a full trim-out including post caps. No change orders, no re-pricing at the door. Every job ships with the 365-Day Done Right Promise: if any part of that fence fails inside a year, we come back and correct it at no charge. Written guarantee, signed by Curtis Lane, in your hand at close.
DIY or Call Us?
You can safely check a few things yourself: walk the line and see which posts move when you push on them, look for brackets that have pulled away from posts, and note any areas where the fence sits below soil grade. That gives you a list of what’s actually failing, which makes your estimate conversation faster and more accurate. Where DIY goes wrong is pulling posts and re-setting footings. Fresno soil is unforgiving, and a post that isn’t set to 24 inches below grade with the right aggregate base will lean inside a year no matter how carefully you brace it. Same goes for re-aligning racked sections: if you don’t reset the corner posts first, you’re just re-racking it in the other direction.
Call (559) 785-2712 and we’ll put a straight number on it. Estimates are free, and you’ll get the number in writing before you decide.
FAQs
A properly installed Tamko composite fence in Fresno should go 20 to 25 years. The panels themselves hold up; what fails first is typically the post footing or the rail brackets, not the material. UV exposure and irrigation overspray are the two conditions that shorten the lifespan here.
Yes, in most cases. If the posts are sound and the issue is isolated to brackets, hardware, or a few cupped pickets, we repair the section rather than replacing the run. We’ll tell you honestly whether a repair will hold or whether you’re pouring money into a fence that’s already racked past the point of no return. Call (559) 785-2712 and we’ll assess it.
Most Fresno residential installations run two to three working days from first post hole to final trim-out. Demo of the old fence typically happens on day one. Weather and hardpan soil can add a day, but we set the schedule in the written estimate so you know what to expect.
We stock the common wear items: OEM post caps, rail brackets, structural screws, and replacement pickets in the standard Tamko colors. If you need something unusual, like a 5×5 post sleeve for an early-2000s run, we order it and usually have it inside a week. We’re an independent service provider and not affiliated with Tamko, but we work with their distribution channel so the parts are legitimate.
Written by Curtis Lane, Owner, Bradford Remodeling Co Fresno at Bradford Remodeling Co Fresno, serving Fresno and nearby areas.
